IC CD4013 PDF

The CD dual D flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors. dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P- channel [ ]. CMOS Dual ‘D’-Type Flip-Flop. Consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q.

Author: Nalabar Tojazshura
Country: Togo
Language: English (Spanish)
Genre: Automotive
Published (Last): 25 July 2007
Pages: 320
PDF File Size: 2.93 Mb
ePub File Size: 9.91 Mb
ISBN: 755-2-40933-174-8
Downloads: 47388
Price: Free* [*Free Regsitration Required]
Uploader: Kimuro

This state was used in the whole circuit.

The IC can be also effectively used for switching any load through input signals received from a sound sensor. Therefore the locker will remain in lock state. Gently adjust and fix the IC on the veroboard somewhere over the center of the board by soldering.

The set up shown can be simply built with the help of the diagram. By using pushbuttons to control the inputs, you can see exactly how the flip flop reacts to changes in inputs. The demand for Electronic locks is high since it offer high security and easy to handle rather than the mechanical locks.

In this circuit, we will operate the flip flop using nothing but manual pushbutton control. If we don’t change the values of the pins, the outputs retain their values. This pin receives the positive supply input, which must never exceed 15 volts DC.

The can actually take a wide range of voltage, anywhere from 3VV. A is grounded and this in turn gives low output at pin 1 Q when positive edge is encountered in the CLK pin of U1: Or a timer chip.

The is a dual D flip flop chip. Positive input Pin After all the connections are made, have a quick glance and make sure that all have been wired as per the diagram, if possible brush-clean the solder side with thinner.

  INSUFICIENCIA VERTEBROBASILAR TRATAMIENTO PDF

Pin 7 is the ground or negative supply input of the IC. In the above circuit the Switches 1,3,5,8 are wired to feed the clock pulse to each flip flop units U1: Because they store bits, they form the basis of memory, cd4031 storage. However, in this circuit, we will simply show how to operate 1 of them.

If the set pin is 0 and the reset pin is 0, while the D pin is X, then the Q output and the Q retain their previous value. Most of the E-locks in the market are cost more and not everyone could afford buying these locks. This means it’s composed of 2 independent flip flops.

How the Circuit Works This circuits through manual pushbutton control.

CD – Dual D Flip Flop

The operation of a D type Flip flop is as follows: The clock pin is the pin where we feed a clock signal. Flop flops have many applications. B will gives a low signal which in turn turns the PNP transistor ON and therefore the relay gets activated.

The operation of a single D type Flip flop unit is very important to understand the working principle of the above circuit. In this circuit, we show how to build a D flip flop circuit with a D flip flop chip. The circuit shown can be used for toggling any load simply by touching the touch pad. Pinouts of the IC The D-type blocks consist of four inputs, explained as follows: B, this will place the low signal in it.

The is composed of 2 independent flip flops, labeled on the input as flip flop 1 and flip flop 2. Pin 5 is the data pin. For other configurations this input is terminated to any of the logic levels, i.

  CHELONIA AGASSIZII PDF

This input is used for receiving clock signals which are normally in the form of square waves. The signals produces a bistable effect over one of the free outputs, the other being connected to the Data input as explained above.

IC, CD, Dual D Flip-Flop

Set and Reset Inputs Pins 4, 6 and 10, 8: We have 3 pushbuttons connected to the 3 inputs of the flip flop chip. If the set pin is 1 and the reset pin is 0 D is Xthen the Q output is 1 and the Q output is 0. Initially D pin of the U1: This operation principle forms backbone of the above code locker.

It can be obtained at Tayda Electronics at the following link: This is only case when both outputs will be HIGH.

It means it doesn’t matter what logic state the data input is in. So this is a toggle application for the D flip flop.

Understanding IC 4013 Pin-Outs and Specifications – Datasheet and Application Circuits Explained

Here we can see how the above discussed operating principle of the IC is practically set up for a useful purpose. B, this will force the Q pin of U1: We connect a clock signal to the clock of thewhich is pin 3. This clock pin can be obtained from a number of sources such as a frequency generator. The configurations can be repeated by connecting the modules in series for getting the time period to any desired lengths, but in multiples of two.

The following two tabs change content below.