GRAPHTEC FC8000 MANUAL PDF

Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.

Author: Fautaur JoJogis
Country: Botswana
Language: English (Spanish)
Genre: Art
Published (Last): 18 October 2013
Pages: 100
PDF File Size: 9.72 Mb
ePub File Size: 15.78 Mb
ISBN: 300-5-91262-551-2
Downloads: 62653
Price: Free* [*Free Regsitration Required]
Uploader: Arashizilkree

When Feeding Long-axis Media at least 2 meters Position the push rollers at least 15 mm inside the edges of the media. Page Press the [1] key.

Graphtec Manuals and Drivers – SignWarehouse Product Support

Page 13 Options Page Press the [1] key RSC. Page Repeat steps 3 to 5 and select the 4 values to be set. It will return to default screen. Supported the standard crop grapntec The axis alignment can be performed using by printed industry standard crop mark for shear.

Loading Sheet Media Operation Lower the media set lever to raise the push rollers. The first registration mark is automatically detected within a wide search area including the negative area from the starting point; this eliminates the need to manually move the sensor near the registration mark position. Setting the Step Pass It may not cut the curved line smoothly if there is very short lines in the hraphtec.

Number of the MARK TYPE2 is used when you would like to use as much area registration mark will be different for the possible on the media as cutting area. Make sure that the tool bracket is engaged on the tool’s fange, and fraphtec tighten the screw.

  BEST OF BUKAS PALAD PDF

Pass the leading edge from the front of the plotter so it emerges from the back. Flange Bracket to hold tool Setting Regarding Cutting Qua Automatically Cross Cut It will automatically cross cut after cutting when the cutting is done with provided software.

Digits of the setting can be changed by pressing the [FAST] key. Using the Loupe Use your finger to put the loupe in the pen down status. All the operations described in this chapter is to start from the READY status media is set as a general condition.

For front loading For rear loading Joint Dual Configuration FC can save 2 sets of settings independently.

GRAPHTEC FC8000 SERIES User Manual

Press the [1] key X. Setting Cutting Width Set the cutting width. Name of the button and corresponding function is displayed on the screen when a function is allocated to the button on the control panel.

While pushing the tool holder in the upward direction, push the CAUTION pouncing tool all the way into the holder until its fange contacts Position the media and the push rollers to correspond with the width of the media. Basket x 1, basket tubes long x 3, basket tubes short x 4, joints x 4, mounts x 2, socket cap head screws x 4, use Allen wrench to assemble the basket.

The configuration regarding the output device in the application software has changed. Connect one end of the provided power cord to the FC AC line inlet and the other end to an maual socket of the rated supply voltage.

  IFAK CONTENTS PDF

Press the [2] key TOOL. Press the [1] key RSC. It is possible to cut at any location manually, or to automatically cut when the cutting is completed.

Tool carriage will move away to upper right by continuously performing the same operation. Good Loupe Center of target point Perform further adjustment by performing cutting test after adjusting the blade length manually.

It will be set to mode for apparel when the apparel AP mode is set on. Change the color of the registration mark.

Using the Loupe your manuao to put the loupe in the pen down status. Possible Cause Solution E The plotter is defective. Load the media according to the instructions given for each type. It is possible to quickly switch the different settings by the dual Cutting data will be cleared when USER is configuration.

What is the registration mark? Supplement This setting is maintained even if the power is turned off.

Cross Cut Manually Cross Cut Manually is cross cut at the position 15 mm behind the last cut position.